| 1. Execute actions for a decompression of fuel system (see subsection 5.2). |
| 2. Disconnect the battery from weight. |
| 3. Remove the battery and a tray of the battery. |
| 4. Remove a cowl, having spread a sheeting (see subsection 11.8). |
| 5. Remove the air filter (see subsection 5.9). |
| 6. Lift the car and establish on supports. Merge liquid from the cooling system, oil from the engine and take off drive belts (see subsection 2.6.4). |
|
7. Apply accurate tags on hoses of the cooling system and decrease in toxicity of exhaust gases, on vacuum hoses, sockets of conducting, the tire of connection with weight and fuel pipes. Paste the put tags an adhesive tape or you put with paint that they were well visible. Make instant pictures or sketch a relative positioning of details and arms. |
| 8. Remove a washer reservoir of a windshield and a tank of cooling liquid. |
| 9. Remove the fan(s) and a radiator (see subsection 4.8 and subsection 4.5). |
| 10. Disconnect heater hoses. |
| 11. Dump the residual pressure of fuel in a tank for what turn off a stopper of a jellied mouth and disconnect fuel tubes from the engine (see subsection 5.2). |
| 12. Disconnect draft of a butterfly valve, draft of the throttle valve of transmission and a cable of gear shifting on the engine (if is available). |
| 13. Remove the battery and a tray of the battery (see subsection 3.3.2). |
| 14. Remove the soaking-up and final collectors, being guided by the description in subsection 3.1.1.4 and subsection 3.1.1.5. |
| 15. On the cars equipped with the hydraulic booster turn off bolts of the pump of the hydraulic booster. If there is enough place, then bind the pump, having taken aside, not disconnecting hoses. If necessary disconnect hoses (see subsection 10.19). |
Prevention
Tie up the compressor a wire, do not assume that it hung on hoses.
|
| 16. Attach slings to the engine, bring таль the elevator and fix slings on a waist. Choose a weak point to a small tension of a waist. |
| 17. Remove half shafts (see subsection 8.3). |
| 18. Turn off a coupling bolt of a back support of the engine (from a wall of a motor compartment), get rubber caps from a longitudinal longeron of a support of the engine and turn off four nuts and five bolts (see subsection 7.1.5). |
| 19. Take off drive belts, a pulley of the pump of cooling liquid and a pulley of the crankshaft. |
| 20. Turn off a bolt of fastening of a support of the engine from a radiator to the chassis. |
| 21. On the cars equipped with automatic transmission get the plastic filter from the lower part of a case of transmission. Turn off bolts of fastening of the hydrotransformer to a drive plate
(see subsection 7.2.8) and slightly give the hydrotransformer towards transmission. |
| 22. Turn off bolts of fastening of transmission to the engine and separate the engine from transmission (see subsection 7.1.5). The hydrotransformer has to remain on transmission. |
Prevention
If with the engine also transmission is removed, then it is necessary to disconnect the left support of the engine, cables, conducting and hoses from transmission. Not to turn off bolts of fastening of transmission to the engine at this stage.
|
| 23. Be once again convinced that all details connecting the engine to a body or transmission are removed. Remove all remained details previously having marked. |
| 24. Record a transmission case, having established a support and having laid a board not to damage a case. Turn off bolts of support of the engine, except those which belong to transmission. |
Prevention
After posting of the power unit performance of any works under the engine or transmission is forbidden.
|
|
25. Carefully lift the engine (or the power unit assembled) from a motor compartment. If necessary wring out support from engine frame arms. |
Prevention
At dismantle of the engine from the car equipped with the manual transmission in that case when the check point remains on the car, it is required to lower the check point by means of a support. It is necessary to incline the engine and to get it from a motor compartment.
|
|
|
26. Take the engine aside from the engine and carefully lower against the stop in a floor, or remove a drive plate (coupling) and install the engine on the stand or a workbench. |
Prevention
On the cars equipped with automatic transmission apply tags on internal and external remote washers (if are available) and you store washers together with a drive plate.
|
