Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
12.1. Safety locks
12.2. The burned-through crossing points
12.3. Automatic switches
12.4. Relay
12.5. Breakers of indexes of turns / alarm system
12.6. The combined switch
12.7. The switches installed on a steering column
12.8. Lock of ignition and drum of the lock
12.9. Switch of a heater of back glass
12:10. Heater of back glass
12:11. Radio receiver and loudspeakers
12:12. Antenna
12:13. Bulbs of headlights of head light
12:14. Headlights of head light
12:15. Replacement of bulbs
12:16. System of day inclusion of headlights
12:17. Engine of screen wipers
12:18. Instrument guard
12:19. Sound signal
12:20. System cruise control
12:21. System of the central lock
12:22. System of window regulators
12:23. Rear-view mirrors with the electric drive
12:24. Safety airbag
+ 12:25. Electrical circuitries
|
Prevention
On these models the airbag of safety which can reveal (to be filled with air) when it is connected to the accumulator is installed. Disconnect a wire of the negative plug of the accumulator and wait at least two minutes before work with the safety airbag.
If the stereoplayer of your car has system of the coding, check whether you know a code of activation of the player before an accumulator detachment.
Elements of the combined switch installed on a steering column
|
1. Spring
2. Ball
3. Contact of a sound signal
4. Connection socket
|
5. Switch of screen wipers
6. Switch of passing / driving beam of headlights
7. Basis
8. Switch of headlights |
Removal
| PERFORMANCE ORDER |
| 1. Disconnect a wire of the negative plug of the accumulator. |
| 2. Remove a casing of a steering column (see subsection 11.22) both the lower panel of finishing and (subsection 11.23). |
| 3. Walk along a plait of wires of that switch which is subject to check, to the connection socket. |
|
Table of connection of a tester and conductivity of the switch of headlights
|
|
1. Indexes of turns on the right side of the car
2. Alarm system
3. Indexes of turns on the left side of the car
4. I will corrode connections of the combined switch |
Table of connection of a tester and conductivity of the switch of indexes of turns
|
|
1. Indexes of turns on the right side of the car
2. Alarm system
3. Indexes of turns on the left side of the car
4. I will corrode connections of the combined switch |
Table of connection of a tester and conductivity of the switch of washers and screen wipers of a windshield
|
a). The switch of screen wipers with function for driving in fog
1. An operating mode of screen wipers for driving in fog
2. It is included
3. Low
4. High
|
b). The switch of screen wipers with function of faltering work
1. It is included
2. Faltering
3. Low
4. High
с). I will corrode connections In the combined switch |
Table of connection of a tester and conductivity of the switch of washers and screen wiper of back glass
|
|
and. Washer
b. I will corrode connections In the combined switch |
Check
| PERFORMANCE ORDER |
| 1. Disconnect the socket of connection and, by means of an ohmmeter check conductivity of a chain between the specified plugs when switches are in each of the specified provisions. |
| 2. If current is not carried, replace the faulty switch. |
|
Replacement
| PERFORMANCE ORDER |
| 1. Remove the combined switch (see subsection 12.6). Turn off four screws fixing a spiral wire of the airbag of safety and remove a wire from the combined switch. |
| 2. Turn off fixing screws of the switch which needs to be replaced and remove the faulty switch. |
| 3. Get wires of the replaced switch from the general plait of wires and disconnect them from the connection socket. |
| 4. Get wires of the replaced switch from the general plait of wires and disconnect them from the connection socket. |
|
5. Wring out uvulas behind the socket of connection and uncover. In front of the socket of connection insert the small screw-driver or a spoke and wring out the latch holding contact, get contact behind the connection socket. |
| 6. Come into contacts of the new switch in the connection socket, having inserted them so that latches reliably recorded contacts. |
| 7. Further, installation is carried out upside-down removals. Being guided by instructions, (see subsection 10.16) adjust the wire twirled by a spiral before installation of a steering wheel. |
|
|
|
