Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. The burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches installed on a steering column
   12.8. Lock of ignition and drum of the lock
   12.9. Switch of a heater of back glass
   12:10. Heater of back glass
   12:11. Radio receiver and loudspeakers
   12:12. Antenna
   12:13. Bulbs of headlights of head light
   12:14. Headlights of head light
   12:15. Replacement of bulbs
   12:16. System of day inclusion of headlights
   12:17. Engine of screen wipers
   12:18. Instrument guard
   12:19. Sound signal
   12:20. System cruise control
   12:21. System of the central lock
   12:22. System of window regulators
   12:23. Rear-view mirrors with the electric drive
   12:24. Safety airbag
   + 12:25. Electrical circuitries

ai chat

12:14. Headlights of head light

GENERAL INFORMATION

Screws of adjustment of headlights of head light

1. The screw for adjustment in the horizontal plane

2. The screw for adjustment in the vertical plane

It is very important that the direction of a beam of headlights of head light was correctly adjusted. At the wrong adjustment of a headlight can blind the driver of the oncoming car and lead to the road accident or seriously reduce for you visibility of the road.

It is necessary to check adjustment of headlights of head light each 12 months and every time after installation of new headlights or repair of a forward part of a body of the car.

It is necessary to emphasize that the operation on adjustment described below is only a temporary measure until headlights of head light are adjusted in the auto repair shop having the necessary equipment.

Adjustment

PERFORMANCE ORDER

1. On these models two adjusting screws are provided, one is located sideways and controls the movement to the left – to the right and one from below and controls the movement up – down. Access to them can be got behind a headlight.

2. There are several methods of adjustment of headlights of head light. When using the simplest method, the pure wall, an adhesive tape and an equal floor is necessary.

3. Paste two strips of an adhesive tape vertically on a wall on the middle of each of headlights of head light, at height of headlights.

4. Paste the second strip of an adhesive tape on a wall horizontally on the center of headlights of head light. The tape on a wall will be easier to be pasted if to park the car in only several centimeters from a wall.

5. Adjustment needs to be carried out when the car costs on a plain surface, at distance in 8 meters from a wall, the fuel tank has to be half filled, and in the car there should not be too heavy freight.

6. Since adjustment of headlights of passing beam, establish a zone of the brightest light of headlights 5 cm lower than the horizontal line and on 5 cm from the vertical line to the right. Turning adjusting screws, finish the required direction of a beam.

7. At the switched-on high beam headlamps, the zone of the largest brightness has to precisely on the center of vertical strips, is slightly lower than a horizontal strip. Perhaps, you not manage to establish headlights so that precisely to adjust the direction of a beam for near and far light of headlights. If you have to make a compromise between these two adjustments, do not forget that passing beam of headlights is used more often and has bigger value for safety of driving.

8. Without postponing, address experts for adjustment of headlights of head light.

Removal

PERFORMANCE ORDER

1. Disconnect a wire of the negative plug of the accumulator. Prevention If the stereoplayer of your car has system of the coding, check whether you know a code of activation of the player before an accumulator detachment.
2. Remove a lattice of facing of a radiator (see subsection 11.26).
3. Remove a parking headlight (see subsection 12.15).
	4. Turn off fixing a bolt of fastening of a headlight of head light to a radiator cross-piece.
	5. After removal of a parking lamp, it is possible to get access to two side fixing nuts (are specified by shooters).
	6. Get a headlight forward to disconnect fastening in a bottom corner (it is specified by an arrow).
7. Remove a bulb (see subsection 12.13).
8. Installation is carried out upside-down removals.

home