Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
- 12. Electric equipment
   12.1. Safety locks
   12.2. The burned-through crossing points
   12.3. Automatic switches
   12.4. Relay
   12.5. Breakers of indexes of turns / alarm system
   12.6. The combined switch
   12.7. The switches installed on a steering column
   12.8. Lock of ignition and drum of the lock
   12.9. Switch of a heater of back glass
   12:10. Heater of back glass
   12:11. Radio receiver and loudspeakers
   12:12. Antenna
   12:13. Bulbs of headlights of head light
   12:14. Headlights of head light
   12:15. Replacement of bulbs
   12:16. System of day inclusion of headlights
   12:17. Engine of screen wipers
   12:18. Instrument guard
   12:19. Sound signal
   12:20. System cruise control
   12:21. System of the central lock
   12:22. System of window regulators
   12:23. Rear-view mirrors with the electric drive
   12:24. Safety airbag
   + 12:25. Electrical circuitries



bbeb4949

12:15. Replacement of bulbs

GENERAL INFORMATION

Clips of the panel of finishing of a luggage carrier

1. Removal


2. Installation

FORWARD PARKING HEADLIGHTS AND SIDE INDEXES OF TURNS

PERFORMANCE ORDER
1. Turn off the fixing screw (it is specified by an arrow) and remove a headlight, having pushed it forward (in the direction of an arrow).
2. Disconnect the socket of connection and turn cartridges with bulbs counterclockwise for replacement of bulbs.

INDEXES OF TURNS

PERFORMANCE ORDER
1. Turn off fixing screws and get a headlight from a bumper, having turned it.
2. Disconnect the socket of connection and turn a cartridge with a bulb counterclockwise for its removal.

BULBS OF BACK SIDE INDEXES OF TURNS, HEADLIGHTS OF THE STOPLIGHT, BACK INDEXES OF TURNS, DIMENSIONAL HEADLIGHTS AND HEADLIGHTS OF THE BACKING

PERFORMANCE ORDER
On models with a body like Sedan
1. Turn off two screws fixing a block headlight, open a luggage carrier and remove the finishing panel for receiving access, then turn off a nut and get a back block headlight.
2. Turn cartridges of bulbs counterclockwise, get them and replace bulbs.
On models with a body like Versatile person
3. Turn off the fixing screw and lift a block headlight for its removal up.
4. Turn cartridges of bulbs counterclockwise, get them and replace bulbs.

BULBS OF ILLUMINATION OF REGISTRATION PLATE

PERFORMANCE ORDER
On models with a body like Sedan
1. Press on a uvula and lower the lens of a lamp for receiving access to a bulb down.
2. Turn a cartridge of a bulb counterclockwise and remove it.
On models with a body like Versatile person
3. Turn off screws of fastening of a lamp of illumination of registration plate and lower a lamp.
4. Remove the holder of a bulb, having turned him counterclockwise, then get a bulb from the boss.

THE STOPLIGHT LAMP LOCATED ON THE CEILING OF SALON BEFORE BACK GLASS

PERFORMANCE ORDER
On models with a body like Sedan
1. By means of a ball pen press on the center of fastenings, and then remove fastenings by means of the screw-driver and remove a headlight casing.
2. Turn off bolts of fastening of a lamp, lift a lamp for receiving access, then turn a cartridge with a bulb counterclockwise for its removal and get a bulb, having just pulled it on themselves.
On models with a body like Versatile person
3. Remove the lens of a bulb, remove the holder of a bulb, having turned it counterclockwise, then get a bulb from the boss.

BULBS OF ILLUMINATION OF SALON

PERFORMANCE ORDER
1. By means of the small screw-driver remove lenses.
2. Get a bulb from contacts. Perhaps, you should hook a bulb the screw-driver, in this case, hook edge of a bulb (otherwise glass can burst).

BULBS OF ILLUMINATION OF THE INSTRUMENT GUARD

PERFORMANCE ORDER

1. For receiving access to bulbs of illumination of an instrument guard, it needs to be removed (see subsection 12.18).

2. Accurately take a bulb clip aside (it is specified by an arrow) and get a bulb. Bulbs can be established behind an instrument guard.