Toyota Corolla

1992-1998 of release

Repair and operation of the car



Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
- 9. Brake system
   9.1. Specifications
   9.2. System of anti-blocking of brakes (ABS)
   9.3. Brake shoes of forward brakes
   9.4. Support of forward brakes
   9.5. Brake shoes of back disk brakes
   9.6. Support of back disk brakes
   9.7. Brake disk
   9.8. Brake shoes of back drum brakes
   9.9. Working cylinder
   9.10. Main cylinder of the brake system
   9.11. Brake hoses and tubes
   9.12. Hydraulic system of brakes
   9.13. Vacuum amplifier
   9.14. Emergency brake
   9.15. Ropes of the emergency brake
   9.16. Brake pedal
   9.17. Switch of headlights of a stoplight
   9.18. Valve of restriction of pressure sensitive to car loading
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment



bbeb4949

9.15. Ropes of the emergency brake

Replacement

PERFORMANCE ORDER
Ropes between the equalizer and brakes
1. Turn off nuts of fastening of back wheels, lift a back part of the car and establish it on support. Block forward wheels. Remove a back wheel.
2. Check that the car did not stand on the emergency brake, then, on drum brakes, remove the brake drum.
3. On models with drum brakes remove brake shoes and disconnect a rope from the lever of the emergency brake (see subsection 9.8). Turn off two fixing bolts (are specified by shooters) a rope on a guard of a back brake and pull out a rope through an opening in a guard.
4. On models with disk brakes disconnect a rope from a support, having got the check and a pin, at the same time pressing the cranked lever of the emergency brake. Remove a fixing clip of a braid of a rope and remove a rope.
5. Turn off a fixing nut of a clip near forward fastening of longitudinal draft.
6. Turn off a bolt (it is specified by an arrow) fastenings of a clip of a rope to the floor panel.
7. Remove thermal screens of an exhaust pipe and the catalytic converter (see subsection 6.9).
8. Turn off fixing bolts of clips (are specified by the right shooters). Get nylon plugs from arms (are specified by the central shooters). Disconnect the forward ends of ropes from the equalizer (it is specified by the left shooters).
9. Installation is carried out upside-down removals. Apply a thin film of high-temperature lubricant for the end of a rope which fastens to the equalizer.
10. Adjust the emergency brake after completion of installation of a rope (see subsection 9.14).
Rope between the equalizer and the lever of the emergency brake
11. Remove the central console (see subsection 11.24).
12. When the lever is lowered, turn off a lock-nut and an adjusting nut (see subsection 9.14) and disconnect a rope from the lever.
13. Lift a back part of the car and install it on support.
14. Remove thermal screens of an exhaust pipe and the catalytic converter (see subsection 6.9).
15. Turn the end of a rope on 90 ° and disconnect it from the equalizer.
16. Get the rubber plug from the panel of a floor and get a rope through an opening in the panel.
17. Installation is carried out upside-down removals. Apply a thin film of high-temperature lubricant on the site of a rope which fastens to the equalizer. Also cover edges of the rubber plug with silicone adhesive in order that it did not pass water.

18. Adjust the course of the lever of the emergency brake upon completion of installation (see subsection 9.14).