Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   - 3.2. Diesel engine
      3.2.1. Specifications
      3.2.2. Replacement of a gear belt
      3.2.3. Removal of a head of cylinders
      3.2.4. Dismantling of a head of cylinders
      3.2.5. Partition of a head of cylinders
      3.2.6. Assembly of a head of the block of cylinders
      3.2.7. Installation of a head of cylinders
      3.2.8. Check and adjustment of gaps of valves
      3.2.9. Check of a compression of cylinders
      3.2.10. Pistons and rods
      3.2.11. Measurement of cylinders
      3.2.12. Assembly of pistons and rods
      3.2.13. Installation of pistons and rods
      3.2.14. Bent shaft and flywheel
      + 3.2.15. Cooling system
      + 3.2.16. Lubrication system
      3.2.17. Device of injection of diesel fuel
      3.2.18. Operation of the car on diesel fuel
      3.2.19. Fuel filter
      3.2.20. Fuel pump of high pressure
      3.2.21. Nozzles
      3.2.22. Glow plugs
      3.2.23. Adjustment of the mode of idling
      3.2.24. Adjustment of the maximum turns
      + 3.2.25. Useful tips to owners of the diesel engine
   + 3.3. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.2.8. Check and adjustment of gaps of valves

GENERAL INFORMATION

The sequence of adjustment of gaps of valves at installation of the piston of the first cylinder in the provision of VMT

Е – camshaft of inlet valves

And – the camshaft of final valves

The sequence of adjustment of gaps of valves at installation of the piston of the fourth cylinder in the provision of VMT

Е – camshaft of inlet valves

And – the camshaft of final valves

Use of the special tool for pressing of pushers in their openings

For withdrawal adjusting шаюб the screw-driver and a magnet are used.

On diesel engines gaps of valves are checked and regulated on the cold engine.

PERFORMANCE ORDER

1. Uncover a head of cylinders.

2. Turn the engine before installation of the piston of the first cylinder in the provision of VMT. At the same time the tag on a pulley has to coincide with a pin on the case of the oil pump.

3. Check that pushers of valves of the first cylinder have a small side play, and pushers of valves of the fourth cylinder sit densely. If it not so, turn the engine on one turn.

4. Measure according to rice. The sequence of adjustment of gaps of valves at installation of the piston of the first cylinder in the provision of VMT by means of the probes inserted between a pusher and a surface of a cam, gaps of valves. Gaps inlet (Е) and final (And) valves not on all engines are identical and are given in size tables and adjustments.

5. Turn the engine on one whole revolution and measure the gaps specified rice. The sequence of adjustment of gaps of valves at installation of the piston of the fourth cylinder in the provision of VMT. A sign of the correct adjustment is when the end of the probe is entered, and then under easy pressing the probe caves in and enters inside.

6. For adjustment of gaps of valves it is necessary to replace adjusting washers from the top party of pushers, but removal and installation of adjusting washers requires the special tool. For this purpose turn a bent shaft before installation of the corresponding cam an edge up and by means of the special tool shown on rice. Use of the special tool for pressing of pushers in their openings, or otherwise press a pusher inside that it was possible to take and pull out the small screw-driver and a magnet an adjusting washer.

7. Before pressing a pusher, it should be turned so that the notch from the top party was turned to candles. Both pushers nestle at the same time, that is it is necessary to watch that both pushers nestled adaptation leg.

8. Measure the removed washer by a micrometer and write down result.

9. Calculate thickness of a new washer for providing the required valve gap. At the same time the following formula is used:
Inlet valves: N = T + (And – 0,25 mm);
Final valves: N = T + (And – 0,30 mm), where "T" – thickness of the removed washer. "And" – the measured gap of the valve and "N" – thickness to the new, subject installation of a washer.

10. Choose a washer which on thickness is closest to the required gap. There is a row from 25 sizes of washers from 2,2 mm to 3,4 mm thick through 0,05 mm.

11. For installation of an adjusting washer press a pusher inside again and insert a washer.

12. Measure a valve gap as it was described above.

13. Adjust gaps of other valves.

Prevention

The adjusting washer should not fall in the engine at all. In order to avoid it use the small screw-driver and a magnet as it is shown on rice. Use of the special tool for pressing of pushers in their openings. The washer can be put forward aside and "grabbed" with a magnet after that.

home