Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   - 3.2. Diesel engine
      3.2.1. Specifications
      3.2.2. Replacement of a gear belt
      3.2.3. Removal of a head of cylinders
      3.2.4. Dismantling of a head of cylinders
      3.2.5. Partition of a head of cylinders
      3.2.6. Assembly of a head of the block of cylinders
      3.2.7. Installation of a head of cylinders
      3.2.8. Check and adjustment of gaps of valves
      3.2.9. Check of a compression of cylinders
      3.2.10. Pistons and rods
      3.2.11. Measurement of cylinders
      3.2.12. Assembly of pistons and rods
      3.2.13. Installation of pistons and rods
      3.2.14. Bent shaft and flywheel
      + 3.2.15. Cooling system
      + 3.2.16. Lubrication system
      3.2.17. Device of injection of diesel fuel
      3.2.18. Operation of the car on diesel fuel
      3.2.19. Fuel filter
      3.2.20. Fuel pump of high pressure
      3.2.21. Nozzles
      3.2.22. Glow plugs
      3.2.23. Adjustment of the mode of idling
      3.2.24. Adjustment of the maximum turns
      + 3.2.25. Useful tips to owners of the diesel engine
   + 3.3. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.2.6. Assembly of a head of the block of cylinders

PERFORMANCE ORDER

1. Clear all details of a head of cylinders and spread out them on a workbench so that they lay in an assembly order.
2. If valves got used, they have to be installed surely in the corresponding saddles as the grinding picture of all valves is various.
3. Clear a crescent cap and the place of its landing in a head of cylinders. Cover a surface of a cap with sealant and insert into a head.
4. Move serially valves into the directing plugs of valves. Cores of valves have to be plentifully greased. At repeated installation of valves insert them into former guides. The same treats also the ground-in valves.
5. Put on maslootrazhatelny caps cores of valves and well press their piece tubes.
6. Install springs of valves on a head of cylinders (at repeated installation of springs on the same valves). Put on the top cups of springs and install the elevator of valves for compression of springs. If the end of a core of the valve acts from the top cup of a spring, insert both halves of crackers of the valve into a pro-point of a core and slowly release the elevator of valves.
	7. Strike with the plastic hammer the top part of cores of valves, as shown in the drawing. At the same time jump out incorrectly sitting halves of crackers of valves. Put a rag for the ends of springs that details did not scatter.
8. Insert pushers and adjusting washers on former places. Grease details.
9. Grease necks of bearings of the camshaft and enclose the camshaft in a head of cylinders. Several times turn a shaft that he sat down in openings of bearings.
	10. Put covers of bearings of the camshaft. Covers of bearings have tags (in a circle) and have to be established according to the figure 6.10, that is the top party of number has to be turned to the forward party of the engine.
11. Wrap bolts of covers of bearings manually. After that tighten bolts for several passes from the center outside the moment of an inhaling of 18 N. of m.
12. Adjust gaps of valves.
13. Tighten a camshaft epiploon flange from the forward party. Cover a surface of a flange with sealant.
14. Install the case of production of liquid with new laying. Tighten six bolts and two nuts m 47 N.' moment.
15. Impose new laying and tighten fuel-supply lines and an inlet collector six bolts and two nuts evenly a cross on a cross m 18 N.' moment.
16. Check purity of surfaces of a head of cylinders and the block of cylinders and surely remove traces of old consolidation. If the block of cylinders was exposed to a sink, remove the detergent remains from carving parts under bolts of a head of cylinders. Now the head of cylinders can be established.

home