Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Petrol engines
   - 3.2. Diesel engine
      3.2.1. Specifications
      3.2.2. Replacement of a gear belt
      3.2.3. Removal of a head of cylinders
      3.2.4. Dismantling of a head of cylinders
      3.2.5. Partition of a head of cylinders
      3.2.6. Assembly of a head of the block of cylinders
      3.2.7. Installation of a head of cylinders
      3.2.8. Check and adjustment of gaps of valves
      3.2.9. Check of a compression of cylinders
      3.2.10. Pistons and rods
      3.2.11. Measurement of cylinders
      3.2.12. Assembly of pistons and rods
      3.2.13. Installation of pistons and rods
      3.2.14. Bent shaft and flywheel
      + 3.2.15. Cooling system
      + 3.2.16. Lubrication system
      3.2.17. Device of injection of diesel fuel
      3.2.18. Operation of the car on diesel fuel
      3.2.19. Fuel filter
      3.2.20. Fuel pump of high pressure
      3.2.21. Nozzles
      3.2.22. Glow plugs
      3.2.23. Adjustment of the mode of idling
      3.2.24. Adjustment of the maximum turns
      + 3.2.25. Useful tips to owners of the diesel engine
   + 3.3. Engine electric equipment
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
+ 10. Suspension bracket and steering
+ 11. Body
+ 12. Electric equipment

3.2.3. Removal of a head of cylinders

GENERAL INFORMATION

Assembly drawing of a head of cylinders

1. Cover of a head of cylinders
2. Laying of a cover
3. Cover of the bearing of a rasproyedelitelny shaft
4. Compensation washer
5. Valve pusher
6. Valve crackers
7. Valve spring cup
8. Valve spring
9. Maslootrazhatelny cap of a core of the valve
10. Valve spring emphasis
11. Valve guide
12. Camshaft
13. Bolt of a head of cylinders
14. Head of cylinders
15. The condensing vstaka
16. Union of connection of a head of cylinders
17. Laying of a head of cylinders

18. Final collector
19. Laying of a collector
20. Camshaft epiploon flange
21. Camshaft cogwheel
22. Top cover of a gear belt
23. Naprvlyayushchy roller of a gear belt
24. Returnable spring
25. Compensation washer
26. Valve saddle
27. Valve
28. Returnable toprlivny tube
29. Nozzle
30. Nozzle nest
31. Epiploon
32. Average cover of a gear belt
33. Rubber tip
34. Current tire
35. Glow plug
36. Laying of a collector
37. Inlet collector

Order of an inhaling of bolts of a head of cylinders

The description of removal and installation of a head of cylinders without removal of the engine is given below.

PERFORMANCE ORDER

1. Switch-off the accumulator.

2. Merge cooling liquid.

3. Remove tubes of nozzles, nozzles and a tube of supply of fuel.

4. Disconnect a food wire from an inlet collector. Remove from candles of 4 rubber tips, turn off 4 nuts, remove the current tire and turn out four glow plugs. Fastening of candles is shown in the right part rice. Assembly drawing of a head of cylinders.

5. Take off a gear belt as it was described in the previous chapter. Remove also a camshaft cogwheel.

6. Disconnect the gas cable mechanism.

7. Pick up the phone of discharge of cooling liquid and a tube of a heater. At the same time the bracket for an engine raising is also released. Under a flange of a tube there is a laying. Disconnect a hose since one end.

8. Turn off from the forward party of the engine an average cover (32) of a gear belt on rice. Assembly drawing of a head of cylinders.

9. Remove six nuts and sealing washers of a cover of a head of cylinders and uncover with laying.

10. Remove a forward lifting bracket of the engine.

11. Evenly cross-wise in the sequence specified rice. An order of an inhaling of bolts of a head of cylinders, turn off eighteen bolts of a head of cylinders.

12. Lift a head of cylinders from pins in a head of cylinders and put it on a workbench. Strong sat down head of cylinders can be separated from the block of cylinders by means of the screw-driver inserted between a head of cylinders and a ledge of the block of cylinders. Do not damage at the same time a head of cylinders. Remove traces of old consolidation. Do not allow hit of the remains of old laying in the block of cylinders.

home