Toyota Corolla

1992-1998 of release

Repair and operation of the car

Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross stability (forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and hug bearing (forward wheel)
   10.9. Stabilizer of cross stability (back suspension bracket) and plug
   10:10. Rack of a suspension bracket (back)
   10:11. Longitudinal draft
   10:12. Cross drafts of a suspension bracket
   10:13. Nave and bearing (back wheel)
   10:14. Arm of a nave of a back wheel
   10:15. Steering
   10:16. Steering wheel
   10:17. Tips of steering drafts
   10:18. Steering transfer
   10:19. Pump of system of strengthening of steering
   10:20. System of strengthening of steering
   10:21. Wheels and tires
   10:22. Adjustment of angles of installation of wheels
+ 11. Body
+ 12. Electric equipment

10.4. Stabilizer of cross stability (forward suspension bracket) and plug

GENERAL INFORMATION

Elements of the stabilizer of cross stability and lever of a forward suspension bracket

1. Stabilizer of cross stability
2. Central section of an exhaust pipe
3. Forward section of an exhaust pipe
4. Laying
5. Suspension bracket cross-piece

6. Plug
7. Washer
8. Suspension bracket lever arm
9. Arm of the stabilizer of cross stability
10. Suspension bracket lever

On an illustration elements of models vypuska1993-1995 are shown. On models since 1996 the vertical bolt instead of a nut and a hinged bolt for fastening of a back part of the lever of a suspension bracket to a cross-piece is used.

Removal

PERFORMANCE ORDER

1. Turn off nuts of fastening of forward wheels. Lift a forward part of the car and install it on support. Put the car on the emergency brake and block back wheels in order that it did not sweep. Remove forward wheels.
	2. Remove connecting drafts of the stabilizer of cross stability having turned off two nuts (specified by shooters) on each of connecting drafts. If the bolt rotates together with a nut, use торцовыйключ to hold a bolt.
	3. Turn off a nut (it is specified by the left arrow) and bolts (are specified by other shooters) fastenings of clips of plugs of the stabilizer (on an illustration the left clip is shown – right it is identical).
4. Turn off bolts of fastening of forward section of an exhaust pipe to the catalytic converter (see subsection 5.13) and take away it down so that it was possible to remove the stabilizer.
5. When the stabilizer of cross stability is removed from the car, remove from it fixing plugs and examine them. If they burst, are worn-out or damaged, replace them.
	6. Also, it is recommended to check connecting drafts of the stabilizer. For this purpose, shake a bolt of the spherical hinge here and there 5–6 times, then establish a nut. By means of a dynamometer key put the clamp on one turn each 2–4 seconds and take readings of a dynamometer key on the fifth turn. It has to show the inhaling moment in 0.54–11.83 N. to m. If is not present, replace connecting draft.
7. Clear installation sites of plugs on a stabilizer bar by means of a rigid wire brush to remove dirt and a rust.

Installation

PERFORMANCE ORDER

1. Grease new plugs with the vegetable oil (used in cookery) for simplification of installation of the stabilizer inside and outside.

Prevention

Do not use mineral oil, petroleum oils or brake fluid – they will damage plugs.

2. Installation is carried out upside-down removals

home