Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
10.1. Specifications
10.2. Rack of a suspension bracket (lobby)
10.3. Suspension bracket rack
10.4. Stabilizer of cross stability (forward suspension bracket) and plug
10.5. Suspension bracket lever
10.6. Spherical hinges
10.7. Rotary fist and nave
10.8. Nave and hug bearing (forward wheel)
10.9. Stabilizer of cross stability (back suspension bracket) and plug
10:10. Rack of a suspension bracket (back)
10:11. Longitudinal draft
10:12. Cross drafts of a suspension bracket
10:13. Nave and bearing (back wheel)
10:14. Arm of a nave of a back wheel
10:15. Steering
10:16. Steering wheel
10:17. Tips of steering drafts
10:18. Steering transfer
10:19. Pump of system of strengthening of steering
10:20. System of strengthening of steering
10:21. Wheels and tires
10:22. Adjustment of angles of installation of wheels
+ 11. Body
+ 12. Electric equipment
|
Removal
| PERFORMANCE ORDER |
| 1. Turn off nuts of fastening of a wheel, lift the car and establish it on support. Remove a wheel. |
2. Turn off bolts of fastening of an arm of a brake hose to a rack
suspension brackets. If on the car the ABS system is installed, remove a plait of wires of the sensor of speed from a rack, having turned off a bolt of fastening of an arm. |
|
3. Turn off two nuts of fastening (are specified by an arrow) are resistant to a rotary fist and beat out bolts by means of the hammer and a punch. |
| 4. Remove a rack from a rotary fist. You watch to stretching the internal CV JOINT of a half shaft. Also, you watch that the rotary fist did not overturn outside and did not hang on a brake hose. |
|
5. Holding one hand a suspension bracket rack with a spring, turn off nuts of the top fastening of a rack to a body (are specified by shooters). Remove a rack with a spring from under a car wing. |
|
Check
| PERFORMANCE ORDER |
| 1. Check a rack for existence of leak of liquid from the shock-absorber, for existence of dents, cracks or other damages which demand replacement of a rack. |
| 2. Check a spring for existence of cracks or the broken-away pieces on a spring covering, (it will lead to a premature exit of a spring out of operation because of corrosion). Examine a spring nest on existence of cuts, consolidations or other damages and wear tracks. |
| 3. If there are any damages or wear tracks, pass to the section describing dismantling of a rack (see subsection 10.3). |
|
Installation
| PERFORMANCE ORDER |
| 1. Establish a suspension bracket rack under the aegis of the car and insert bolts of the top fastening into openings in a body. Acquire nuts. It is the best of all to perform this work together as a rack rather heavy and big. |
| 2. Establish a rotary fist on flanges of a rack and insert two fixing bolts. Put the clamps till the required inhaling moment (see subsection 10.1). |
| 3. Establish an arm of a brake hose on a rack of a suspension bracket and reliably twirl a fixing bolt. If on the car the ABS system is installed, establish a fixing arm of wires of the sensor of speed of rotation of a wheel. |
| 4. Establish a wheel and acquire nuts of fastening of a wheel, then lower the car on the earth and tighten nuts till the required inhaling moment (see subsection 10.1). |
| 5. Tighten nuts of the top fastening of a rack of a suspension bracket till the required inhaling moment (see subsection 10.1). |
| 6. Address to auto repair shop for check and if it is necessary, implementation of adjustment of forward wheels. |
|
|
|
