Toyota Corolla

1992-1998 of release

Repair and operation of the car


Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
   10.1. Specifications
   10.2. Rack of a suspension bracket (lobby)
   10.3. Suspension bracket rack
   10.4. Stabilizer of cross stability (forward suspension bracket) and plug
   10.5. Suspension bracket lever
   10.6. Spherical hinges
   10.7. Rotary fist and nave
   10.8. Nave and hug bearing (forward wheel)
   10.9. Stabilizer of cross stability (back suspension bracket) and plug
   10:10. Rack of a suspension bracket (back)
   10:11. Longitudinal draft
   10:12. Cross drafts of a suspension bracket
   10:13. Nave and bearing (back wheel)
   10:14. Arm of a nave of a back wheel
   10:15. Steering
   10:16. Steering wheel
   10:17. Tips of steering drafts
   10:18. Steering transfer
   10:19. Pump of system of strengthening of steering
   10:20. System of strengthening of steering
   10:21. Wheels and tires
   10:22. Adjustment of angles of installation of wheels
+ 11. Body
+ 12. Electric equipment



bbeb4949

10:14. Arm of a nave of a back wheel
GENERAL INFORMATION
Prevention

The dust formed as a result of wear of brake shoes contains the asbestos hazardous to health. It is forbidden to use solvents on the basis of gasoline for cleaning of the mechanism of brakes. Use only special cleaner for the mechanism of brakes.

Removal
PERFORMANCE ORDER
1. Turn off nuts of fastening of a wheel, lift the car and establish it on support. Block forward wheels and remove a back wheel.
2. Remove the brake drum (on models with back drum brakes) or remove a brake disk and a support of a brake (on models with back disk brakes).
3. Remove a brake hose from an arm on a suspension bracket rack (the clip – is specified by an arrow).
4. Remove a nave of a wheel and the bearing (see subsection 10.13).
5. Remove a guard of a back brake and the mechanism of a brake (on models with back drum brakes). It is not necessary to disassemble the mechanism of brakes or to disconnect a rope of the emergency brake. Suspend a guard together with the mechanism of a back brake on a suspension bracket spring by means of a wire. Do not bend a brake tube.
6. On models with ABS, remove the sensor of speed of rotation of a wheel from a nave arm (see rice. Elements of an arm of a nave, a nave and the hug bearing of a back wheel (model with drum brakes)).
7. Turn off, but do not remove fastening bolts (are specified by shooters) a nave arm to a suspension bracket rack.
8. Turn off and remove a bolt, a nut and washers (are specified by shooters) fixing a nave arm to cross levers of a suspension bracket and remove a bolt of fastening of an arm of a nave to longitudinal draft of a suspension bracket.
9. Remove the turned-off bolts of fastening of an arm of a nave to a suspension bracket rack, supporting an arm that it did not fall, and remove a nave arm from a suspension bracket rack.

Installation
PERFORMANCE ORDER
1. Examine the nave arm plug on existence of cracks, deformation or wear tracks. If it is worn-out, give an arm to auto repair shop for replacement.
2. Establish a nave arm on a suspension bracket rack, having combined openings for two fixing bolts. Insert two fixing bolts and tighten them till the required inhaling moment (see subsection 10.1).
3. Establish a bolt of fastening of cross levers of a suspension bracket to a nave arm, put on washers and put the clamp. Do not put the clamp up to the end so far.
4. Establish longitudinal draft on an arm of a nave and tighten fingers a fixing nut and a bolt.
5. Establish a jack under an arm of a nave and lift it on such height at which it approximately is when the car costs on wheels.
6. Tighten a nut and a bolt of fastening of cross drafts of a suspension bracket till the required inhaling moment (see subsection 10.1). Remove a jack from under a nave arm.
7. On models with ABS, install the sensor of speed of rotation of a wheel on a nave arm.
8. Establish a guard of a back brake on a nave arm, establish a nave and tighten four bolts of fastening of a nave till the required inhaling moment (see subsection 10.1).
9. Establish a brake tube on an arm of a rack of a suspension bracket and fix it by means of a clip. Check that the hose was not overwound.
10. Install the brake drum (see subsection 9.8) or a brake disk (see subsection 9.7) and a support (see subsection 9.6).
11. Establish a wheel and nuts of fastening of a wheel.
12. Lower the car on the earth and tighten nuts of fastening of a wheel till the required inhaling moment (see subsection 10.1).