Toyota Corolla
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling systems, heating
+ 5. Fuel, exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmissions
+ 8. Coupling and half shafts
+ 9. Brake system
- 10. Suspension bracket and steering
10.1. Specifications
10.2. Rack of a suspension bracket (lobby)
10.3. Suspension bracket rack
10.4. Stabilizer of cross stability (forward suspension bracket) and plug
10.5. Suspension bracket lever
10.6. Spherical hinges
10.7. Rotary fist and nave
10.8. Nave and hug bearing (forward wheel)
10.9. Stabilizer of cross stability (back suspension bracket) and plug
10:10. Rack of a suspension bracket (back)
10:11. Longitudinal draft
10:12. Cross drafts of a suspension bracket
10:13. Nave and bearing (back wheel)
10:14. Arm of a nave of a back wheel
10:15. Steering
10:16. Steering wheel
10:17. Tips of steering drafts
10:18. Steering transfer
10:19. Pump of system of strengthening of steering
10:20. System of strengthening of steering
10:21. Wheels and tires
10:22. Adjustment of angles of installation of wheels
+ 11. Body
+ 12. Electric equipment
|
Prevention
On these models the safety airbag is installed. You watch that a shaft the helmsman of a column did not rotate at removal of steering transfer, otherwise, you can damage system of the airbag of safety. To block a shaft of a steering column, turn a key in the ignition lock in position of LOCK before work or stretch a seat belt through a steering wheel and clasp the seat belt lock as usual.
Removal
| PERFORMANCE ORDER |
| 1. Turn off nuts of fastening of forward wheels, lift a forward part of the car and establish it on support. Put the car on the emergency brake and remove forward wheels. Remove antisplash screens of the engine. |
|
2. If on the car the system of strengthening of steering is installed, install the pallet under steering transfer. Disconnect tubes of system of strengthening of steering (are specified by shooters) and close openings of tubes to stop loss of hydraulic liquid and to prevent hit in dirt tubes. |
|
3. Turn off bolts of fastening of a casing of the Universal hinge (only three bolts of fastening of a casing – actually their five are visible and specified illustrations by shooters). Remove a casing of the Universal hinge.
|
|
4. Note position of the Universal hinge in relation to an entrance shaft of steering transfer and turn off a coupling bolt of the Universal hinge (it is specified by an arrow).
|
| 5. Remove tips of steering drafts from levers of rotary fists (see subsection 10.17). |
|
6. Supporting steering transfer, turn off bolts of fastening of an arm of steering transfer to a body. At first turn off the lower bolt and the top nut (are specified by an arrow) the right arm of steering transfer, then turn off a nut and a bolt of left.
|
| 7. Disconnect an intermediate shaft from an entrance shaft of steering transfer and remove steering transfer. |
Prevention
Do not rotate a steering wheel at removal of steering transfer. If the steering wheel was incidentally turned, remove a steering wheel and adjust the rope twirled by a spiral (see subsection 10.16).
|
| 8. Check laying of fastenings of steering transfer for existence of traces of excessive wear or damages and replace them if it is necessary. |
|
Installation
| PERFORMANCE ORDER |
| 1. Establish steering transfer into place and connect the Universal hinge, having combined the marks made before removal. |
| 2. Establish fixing arms and bolts and tighten them till the required inhaling moment (see subsection 10.1). |
| 3. Install tips of steering drafts on levers of rotary fists (see subsection 10.17). |
4. Establish a coupling bolt of the Universal hinge and tighten it
till the required inhaling moment (see subsection 10.1). |
| 5. If on the car the system of strengthening of steering is installed, connect hoses of the pipeline of high pressure and the return pipeline to steering transfer and fill a pump tank with hydraulic liquid of the recommended type (see subsection 2.1). |
| 6. Lower the car on the earth and pump over system of strengthening of steering (see subsection 10.20). |
|
Replacement of covers of steering transfer
| PERFORMANCE ORDER |
| 1. Turn off nuts, lift the car and install it on support. Remove a wheel. |
| 2. Remove a tip of steering draft and a lock-nut (see subsection 10.17). |
|
3. Remove a collar on the external end of a cover of steering transfer by means of flat-nose pliers. |
|
4. Cut off a collar since the internal end of a cover by means of nippers. Remove a cover. |
| 5. Before installation of a new cover, wind a carving on the end of steering draft with the isolating tape not to damage a new cover at installation. |
| 6. Put on a new cover steering transfer so that its edge got to a flute on steering draft, and establish new collars. |
| 7. Shoot the isolating film and establish a tip of steering draft (see subsection 10.17). |
| 8. Establish a wheel and nuts of fastening of a wheel. Lower the car on the earth and tighten nuts of fastening of a wheel till the required inhaling moment (see subsection 10.1). |
|
|
|
